Status: COED

Parcel Id: 16-11-30-4939-00000-0030

Total Square Footage: 0 sqft

Block: 00000

Subdivision: 2263 - PALM COAST INDUSTRIAL PARK PHASE III

Job Phone: 386-313-6950

Location Address: 25 RAILSIDE WAY

Type: BC - BUILDING COMMERCIAL

Issue Date: 03/08/2021

NOC: Unknown

Applicant name: MARK ANTHONY LANGELLO

Owner: V3 LLC

Address 25 RAILSIDE WAY PALM COAST, FL 32137

Lot: 0030

Contracted Stated Job Value: ¤350,000.00

Job Description: BUILDING A - 3 UNIT WAREHOUSE

Type: CN

Contractor

M & M DEVELOPMENT & CONSTRUCTION LLC

Status	Location Address	State License Number	Phone
CANCEL	2323 N. STATE ST BUNNELL, FL 32110	RG291103911 (Exp: 08/31/2023)	386-313-6950

Sub Contractors

CHARLES K DAVIS

Status	Location Address	State License Number	Phone
ACTIVE	3000 E MOODY BLVD BLDG 2 BUNNELL , FL 32110	EC13004270 (Exp: 08/31/2026)	386-931-6614

GLEN WILLIAM KEHLE

Status	Location Address	State License Number	Phone	Fax
ACTIVE	P. O. Box 353511 BUNNELL, FL 32110	CFC057241 (Exp: 08/31/2026)	(386) 447-4249	(386) 437-8488

GARY LLOYD SHEFFIELD

Status	Location Address	State License Number	Phone
ACTIVE	48 EAGLE LAKES DRIVE FLAGLER BEACH, FL 32136	CAC048127 (Exp: 08/31/2026)	386-597-3280

Inspection History

Type	Request Date	Result	Inspector
U - UTILITY COMMERCIAL FINAL	10/26/2021	FINAL APPROVED	DHANEY
Note: THIS IS A REINSPECTION
FIRE FINAL	10/05/2021	APPROVED	LMILLER
Note: New inspection due to canceled inspection New inspection due to canceled inspection THIS IS A REINSPECTION not ready need to complete Fire alarm and Sprinkler permits prior. also need ceiling tiles need to be installed correctly with no gaps, and seal hole in wall at sprinkler inder stairs 10-5-21... notes above resolved
BUILDING FINAL	10/05/2021	CANCELLED BY APPLICANT	WEB
Note: New inspection due to canceled inspection THIS IS A REINSPECTION need tactile signage for ADA per FBC 703
BUILDING FINAL	10/05/2021	FINAL APPROVED	LMILLER
Note: New inspection due to canceled inspection New inspection due to canceled inspection THIS IS A REINSPECTION need tactile signage for ADA per FBC 703 10-5-21... notes above resolved
BUILDING FINAL	10/04/2021	CANCELLED BY APPLICANT	WEB
Note: THIS IS A REINSPECTION need tactile signage for ADA per FBC 703
FIRE FINAL	10/04/2021	CANCELLED BY APPLICANT	WEB
Note: New inspection due to canceled inspection THIS IS A REINSPECTION not ready need to complete Fire alarm and Sprinkler permits prior. also need ceiling tiles need to be installed correctly with no gaps, and seal hole in wall at sprinkler inder stairs
FIRE FINAL	10/01/2021	CANCELLED BY APPLICANT	WEB
Note: THIS IS A REINSPECTION not ready need to complete Fire alarm and Sprinkler permits prior. also need ceiling tiles need to be installed correctly with no gaps, and seal hole in wall at sprinkler inder stairs
U - UTILITY COMMERCIAL FINAL	09/27/2021	CANCELLED BY APPLICANT	DHANEY
BUILDING FINAL	09/27/2021	Disapproved - NO FEE	LMILLER
Note: need tactile signage for ADA per FBC 703
FIRE FINAL	09/27/2021	Disapproved - NO FEE	LMILLER
Note: not ready need to complete Fire alarm and Sprinkler permits prior. also need ceiling tiles need to be installed correctly with no gaps, and seal hole in wall at sprinkler inder stairs
PLUMBING FINAL	09/24/2021	APPROVED	PBUCKLEY
HVAC FINAL	09/24/2021	APPROVED	PBUCKLEY
ELECTRIC FINAL	09/24/2021	APPROVED	RMARTIN
ELECTRIC - EARLY POWER	09/17/2021	APPROVED - AS NOTED	RMARTIN
Note: EMAILED FPL RELEASED POWER 11:10
ELECTRIC - EARLY POWER	09/16/2021	CANCELLED BY APPLICANT	WEB
ELECTRIC - EARLY POWER	09/16/2021	Disapproved - NO FEE	RMARTIN
Note: APPROVED PLAN DOES NOT MATCH WHAT IS INSTALLED, NEED REVISION SHOWING CHANGES
EXTERIOR ARCHITECTURAL FEATURES	09/16/2021	APPROVED	JHARDING
GRAVITY SEWER	07/23/2021	APPROVED	JGIBSON
BLD - SEWER TIE IN	07/23/2021	APPROVED - AS NOTED	JGIBSON
Note: NO U-SEWER TIE IN ON BUILDING PERMIT, BUT WAS ON CSD PERMIT USEWR CONNECTION APPROVED AS WELL
DOWN CELL	06/21/2021	APPROVED	FWILLIS
ABOVE CEILING	06/21/2021	APPROVED - AS NOTED	RMARTIN
Note: NO PLUMBING, WILL LOOK AT THE ELECTRIC AND HVAC AT LATER INSPECTION
INSULATION	05/17/2021	CANCELLED BY APPLICANT	WEB
INSULATION	05/17/2021	APPROVED	FWILLIS
FRAMING	05/17/2021	CANCELLED BY APPLICANT	WEB
FRAMING	05/17/2021	APPROVED	FWILLIS
ROOF SHEATHING / BRACE / TIE DOWN	05/17/2021	CANCELLED BY APPLICANT	WEB
ROOF SHEATHING / BRACE / TIE DOWN	05/17/2021	APPROVED	FWILLIS
PLUMBING 2ND ROUGH	05/17/2021	CANCELLED BY APPLICANT	WEB
PLUMBING 2ND ROUGH	05/17/2021	APPROVED - AS NOTED	JGIBSON
Note: NEED STRAPS ON WATER LINES FROMMOP BASIN ACROSS WHERE ROLL UP GARAGE DOOR IS AT, NAIL PLATES ON FRAME WALL AT WATER HEATER
ELECTRIC 2ND ROUGH	05/17/2021	CANCELLED BY APPLICANT	WEB
ELECTRIC 2ND ROUGH	05/17/2021	APPROVED	JMUNSON
HVAC ROUGH	05/17/2021	CANCELLED BY APPLICANT	WEB
HVAC ROUGH	05/17/2021	APPROVED	CPISCITELLI
FOUNDATION SURVEY - OFFICE USE ONLY	05/14/2021	APPROVED	DLEAP
INSULATION	05/11/2021	CANCELLED BY APPLICANT	WEB
STOREFRONT	05/05/2021	APPROVED	FWILLIS

Review History

Department	Status	Date In	Date Out
ELEC	COMPLETE	09/16/2021	09/17/2021
Note: Released By: HAROLD ALLEN - (386)986-2357 - HALLEN@PALMCOASTGOV.COM
ENGIN1	COMPLETE	05/13/2021	05/14/2021
Note: Released By: DENNIS R. LEAP, P.E. - - DLEAP@PALMCOASTGOV.COM
DSD	COMPLETE	05/13/2021	05/14/2021
Note: Released By: JACQUELINE GONZALEZ - (386)986-3751 - JGONZALEZ@PALMCOASTGOV.COM Per dennis leep okay to release.
DSD	CANCEL	05/10/2021	05/13/2021
ENGIN1	HOLD	05/10/2021	05/11/2021
Note: Held By: DENNIS LEAP - - DLEAP@PALMCOASTGOV.COM 1. Plan to be labeled as Foundation Survey. 2. Plan to be signed and sealed.
ELEC	COMPLETE	03/03/2021	03/04/2021
Note: Released By: JOSH MUNSON - (386)986-4736 - JMUNSON@PALMCOASTGOV.COM
FI1	COMPLETE	03/03/2021	03/05/2021
Note: Released By: WILLIAM MILLER - (386)986-3783 - WMILLER@PALMCOASTGOV.COM
PLUM	COMPLETE	03/03/2021	03/05/2021
Note: Released By: PATRICK BUCKLEY - (386)986-3786 - PBUCKLEY@PALMCOASTGOV.COM
BLD	COMPLETE	03/03/2021	03/05/2021
Note: Released By: PATRICK BUCKLEY - (386)986-3786 - PBUCKLEY@PALMCOASTGOV.COM
MECH	COMPLETE	03/03/2021	03/04/2021
Note: Released By: CHRIS PISCITELLI - - CPISCITELLI@PALMCOASTGOV.COM
ELEC	HOLD	01/29/2021	02/01/2021
Note: Held By: JMUNSON Electric load calcs are not done for a commercial building. NEC 2014 220.12, 220.14
MECH	COMPLETE	01/29/2021	02/01/2021
Note: Released By: CPISCITELLI
FI1	HOLD	01/29/2021	02/04/2021
Note: Held By: WMILLER Still need the following... 1. Classification of contents 6.2.1.2 Hazard of contents needs to be classified by the registered design professional (RDP) and submitted for review and approval on the basis of the character of the contents in the building or structure. 2. Please show travel distance from the most remote location to the exits (including above office area).
BLD	HOLD	01/29/2021	02/16/2021
Note: Held By: PBUCKLEY 1. Upload Plan Sheets F1, F2, and F3 provided by the steel building manufacturer. Ensure plans are signed and sealed by the P.E. of record. Previous plan sheets were not signed and sealed and also had a boxed checked that they were for the steel erector only. Either uncheck all boxes or check the box for Construction Permit Set. 2. Repeating Comment from 1st review. Structural foundation Plan Sheet S1 does not indicate the presence of any interior footings to support mezzanine floor construction of 50 p.s.f. Foundation engineer of record to verfify in writing by letter that the slab is capable of supporting live and dead loads from walls supporting mezzanine based on the imposed loads. 3. Add floor trusses to deferred submittal list. A set of floor truss plans signed and sealed by a Florida P.E. are requried to be submitted when plans are ready - same as would be done for roof truss plans. Be sure the floor truss plans include proper live and dead loads.
PLUM	HOLD	01/29/2021	02/16/2021
Note: Held By: PBUCKLEY All references below to the 2017 Florida Building Code-Plumbing The job description provided by the Plumbing Contractor does not satisfy the plan review comments from the intial review. Additionally, the mezzanine now depics a bathroom and the plumbing riser diagram on Plan Sheet A4 does not show any DWV piping to the second flloor. 1. Based on the estimated number of plumbing facilities the building drain shall be 4 inch minimum if serving all four tenant spaces. If individual building drains / building sewers are proposed independent to each tenant space please indicate as much and show locations, materials, size, etc. NEW COMMENT: THE RISER DIAGRAM IS UNCLEAR WHETHER BUILDING SEWERS WILL EXTEND TO THE SEWER MAIN AS INDEPENDENT LINES OR IF THEY WILL BE COMBINED. IF COMBINED, THE BUILDING SEWER WILL NEED TO BE 4 INCH TO THE MAIN. IF INDEPENDENT TO THE MAIN, THEN 3 INCH WILL SUFFICE. CLARIFY THE INTENT IN THE RISER DIAGRAM. 2. Provide location, materials specifications and size of building sewer(s) and water service(s). 3. Provide complete water piping and drain, waste and vent material schedule. 4. Provide location and specifications for water heater in proposed tenant space.
UD1	COMPLETE	01/14/2021	01/21/2021
Note: Released By: CJOHNSON
ELEC	HOLD	01/14/2021	01/27/2021
Note: Held By: JMUNSON 1. Submit electrical load calculations. 2.Panel schedule needs to match the riser diagram 3. Need to comply with 2017 FBC Energy code completion requirements 408.3.1
MECH	HOLD	01/14/2021	01/27/2021
Note: Held By: CPISCITELLI 1. Provide Manual N heatload Calculation per C403.2.1 FBC Energy Conservation 2017 6Th Edition. Provide correct form. (Second Request) 2. Duct layout needs to show Return Air in Office 2 per 601.6 FBC Mechanical 2017 6Th Edition (Second Request) 3. Provide details of volume dampers on duct layout per 603.18 FBC Mechanical 2017 6Th Edition (Second Request) 4. Provide Manufacturers specs on fire dampres showing model and UL rating
FI1	HOLD	01/14/2021	01/27/2021
Note: Held By: WMILLER Still need the following... 1. Classification of contents 6.2.1.2 Hazard of contents needs to be classified by the registered design professional (RDP) and submitted for review and approval on the basis of the character of the contents in the building or structure. 2. Please explain the call out for Type-K extinguisher in the legend on the life safety plan. 3. Please show travel distance from the most remote location to the exits (including above office area). NOTE: please place a note stating that separate permits will be required for fire sprinklers and alarms.
PLUM	HOLD	01/14/2021	01/28/2021
Note: Held By: PBUCKLEY SEE BUILDING REVIEW HOLD. PLANS APPEAR NOT TO HAVE BEEN REVISED TO ADDRESS THE INITIAL REVIEW COMMENTS. ALL COMMENTS BELOW ARE REPEATING FROM THE INITIAL REVIEW. All references below to the 2017 Florida Building Code-Plumbing 1. Replace plumbing riser note with note applicable to this building. 2. Based on the estimated number of plumbing facilities the building drain shall be 4 inch minimum if serving all four tenant spaces. If individual building drains / building sewers are proposed independent to each tenant space please indicate as much and show locations, materials, size, etc. 3. Provide complete plumbing equipment schedule. 4. Provide location, materials specifications and size of building sewer(s) and water service(s). 5. Provide complete water piping and drain, waste and vent material schedule. 6. Provide plumbing hanger and support schedule. 7. Remove note indicating duct layout and other partial illegible note. 8. Provide location and specifications for water heater in proposed tenant space.
BLD	HOLD	01/14/2021	01/28/2021
Note: . 4. Provide foundation note indicating foundation is designed in accordance with the geotechnical investigation prepared for this property. Include name of geotechnical engineer, report number and date of report per Chapter 18. 6. Architectural floor plan indicates load bearing walls supporting a second floor. Foundation plan does not indicate the presence of footings under bearing walls. Un-reinforced concrete slabs are allowed to carry 750 p.s.f. loads. Please have foundation engineer check to ensure load bearing walls can be adequately supported by un-reinforced concrete slab per Chapter 19.
ARCHR	COMPLETE	11/02/2020	11/15/2020
Note: Released By: BDAWSON
BLD	HOLD	11/02/2020	11/17/2020
Note: Held By: PBUCKLEY All references below to the 2017 Florida Building Code-Building 1. Life Safety Plan uploaded as Electrical Load Calculations. On resubmittal, upload life safety plan with appropriate name. 2. Provide product approval number for all windows, garage roll-up doors and exterior store-front doors. 3. Revise note at typical non-bearing wall interior wall section. Remove reference to the Florida Residential Code. Note is also partially cut-off. Provide complete notes. Provide grade and species of wood studs. Provide fire blocking detail as wall likely exceeds 10 feet in height between top and bottom plates. 4. Provide detail related to UL File 419 for extending and maintaining fire-resistive construction for each intersecting wall where they connect to exterior fire-rated walls per Chapter 7. 5. Provide rim-joist detail for all wood floor trusses / joists per Section 2308.4.2.3. 6. Provide foundation note indicating foundation is designed in accordance with the geotechnical investigation prepared for this property. Include name of geotechnical engineer, report number and date of report per Chapter 18. 7. Revise soil bearing pressure in Foundation Note No., 8 to reflect soil bearing pressure of 2,500 p.s.f. geotechnical investigation. 8. Architectural floor plan indicates load bearing walls supporting a second floor. Foundation plan does not indicate the presence of footings under bearing walls. Un-reinforced concrete slabs are allowed to carry 750 p.s.f. loads. Please have foundation engineer check to ensure load bearing walls can be adequately supported by un-reinforced concrete slab per Chapter 19. 9. Architectural floor plan indicates stairs leading to a second floor, mezzanine or loft. Provide floor plan for this space. Indicate proposed use of space. Provide other details such as wall construction, ceiling height, location of windows, floor design load based on use of space etc. 10. Foundation Note No. 1 shall also reference ACI 318-14 in addition to the 2017 FBC. 11. Provide plan sheets properly signed and sealed by the architect of record per FS 471.025 and Florida Administrative Code 61G15-23.003. Date shall be provided at each seal per the referenced sections. 12. Provide complete steel building plans signed and sealed by a Florida licensed professional engineer. Steel building plans to include all project design criteria including but not limited to; floor live and dead loads per Section 1603.1.1, roof live and dead loads per Section 1603.1.3 and 1607.12, wind design data per Section 1603.1.4 No’s 1 through 5 and 1609. Designate exposure category per 1609.4. Indicate whether impact resistant coverings are required per Section 1609.1.2.4. Indicate all pressure coefficients per Section 1609.6.4.3 and Table 1609.6.2. 13. Design professional in responsible charge to provide a complete list of deferred submittals by written note(s) on plans. This includes but is not necessarily limited to; any pre-manufactured / factory constructed stairs, guards, equipment platforms, bar joists, fire sprinkler systems (note for fire sprinkler system to include statement that separate permit is required) etc. Provide note indicating any deferred submittals shall be submitted to the Palm Coast Building Department for review and approval prior to installation per Section 107.3.4.1. 14. Provide complete code analysis for proposed building including but not necessarily limited to: proposed occupancy or occupancies per Section 302 through 312. Note: the limited code analysis provided indicates an occupancy category of “S” but the analysis is incomplete. Is the proposed occupancy S-I or S-II? Proposed finished tenant space indicates presence of office, and reception area and second floor or mezzanine making this space a mixed occupancy building including S (I or II) and B (business office) occupancies. All of building will likely be mixed occupancy – B and S (I or II). Please provide analysis answering items below for entire building or each time a tenant space is to be finished an analysis will be required then. Analysis to include: • Allowable floor area versus actual floor area per Section 506 • Area increases, if required, based on occupancy and construction type per Section 506. Include open space and / or fire sprinkler system allowable area and height increases as applicable. • Allowable building height versus actual building height per Section 504 and Section 504.2 if mixed occupancy building • Allowable number of stories versus actual number of stories per Section 504 • Height or number of story increases if required based on occupancy and construction type per Section • Mezzanine / 2nd floor (Tenant Space 1 indicates presence of a mezzanine or second floor) area calculations per Section 505 • Indicate whether separated or unseparated uses occupancies per Section 508. If uses are to be separated then provide separation details per Section 508 and Table 508.4. • Indicate any incidental uses and requirements per Section 509 and Table 509. • Assign building risk category per Section 1604.5 and table 1604.5 or ASCE 7. 15. Provide complete UL File Number for fire resistive rated walls per Section 107.3.5 No. 4. 16. Provide all project design criteria including but not limited to; Floor live and dead loads for each floor per Section 1603.1.1, roof live loads per Section 1603.1.3 and 1607.12, wind design data per Section 1603.1.4 No’s 1 through 5 and 1609. Designate exposure category per 1609.4. Indicate whether impact resistant coverings are required per Section 1609.1.2.4. Indicate all pressure coefficients per Section 1609.6.4.3 and Table 1609.6.2, Indicate load combinations per Section 1604.2 and 1605, dead loads per 1606 and live loads per 1607. Provide other uniformly distributed and concentrated live loads for items such as stairs, stair treads, guards and similar items not mentioned herein per Section 1607 and Table 1607.1. 17. Stair section depicts a guard but floor plan indicates a half-wall with cap. Which is it? 18. Indicate glazing required to be tempered glass in door and window schedule per Section 2406. 19. Provide stair landing dimensions for stair mid-point landing. Stair section appears to conflict with plan view per Section 1014. 20. Provide complete stair section including headroom height. Provide stair handrail detail indicating handrail returns and handrail safety extensions beyond first and last riser of stairs. Show handrail continuous through intermediate landing per Sections 1011, 1014 and 1015. All references below to the 2017 Florida Building Code-Accessibility 1. Provide width of hall and passages per Section 402 and 403.5. 2. Check approach requirements for Door 104. If the hall is less than 48 inches in width, door approach will be considered parallel to latch and hinge side and a 60 inch maneuvering space is required in front of door per Section 404 and Table 404.2.4.1. 3. Provide dimensions of landings at exterior doors including width, length in the direction of travel, maximum allowable running and cross slopes and maneuvering clearances at doors. Door No. 105 does not appear to meet minimum maneuvering clearance on push side of latch. Section 404.2 and Table 404.2.4.1 4. Provide accessible sign detail and location for bathroom per Section 703. 5. Revise door schedule to indicate doors that require kick plates per Section 404.2.10. 6. Identify knee and toe clearances at ADA sink counter section for both the bath lavatory and office sink. 7. Provide mounting location for toilet paper dispenser in relation to water closet per Section 604.7. 8. Provide grab bar blocking and mounting / attachment detail and note indicating blocking and attachments support minimum 250 p.s.f. load per Section 609.8.
DSD	COMPLETE	11/02/2020	11/06/2020
Note: Released By: DRAMIREZ
ELEC	HOLD	11/02/2020	11/10/2020
Note: Held By: JMUNSON 1. Submit electrical load calculations. 2.Panel schedule needs to match the riser diagram 3. Need to comply with 2017 FBC Energy code completion requirements, 405.6.4.1, 405.6.4.2 and 408.3.1 4. Submit interior lighting compliance certificate. FBC Energy code 2017
FI1	HOLD	11/02/2020	11/16/2020
Note: Held By: WMILLER 1. Classification of contents 6.2.1.2 Hazard of contents needs to be classified by the registered design professional (RDP) and submitted for review and approval on the basis of the character of the contents in the building or structure. 2. Please explain the call out for Type-K extinguisher in the legend on on the life safety plan. 3. PLease shoe travel distance from the most remote location to the exits (encluding above office area). NOTE: please be advised the separate permits will be required for fire sprinklers and alarms.
MECH	HOLD	11/02/2020	11/10/2020
Note: Held By: CPISCITELLI 1. Provide Energy Calculations per Section C407 FBC Energy Conservation 2017 6Th Edition. 2. Provide Manual N heatload Calculation per C403.2.1 FBC Energy Conservation 2017 6Th Edition 3. Duct layout needs to show Return Air in Office 2 per 601.6 FBC Mechanical 2017 6Th Edition 4. Provide details of volume dampers on duct layout per 603.18 FBC Mechanical 2017 6Th Edition
PLUM	HOLD	11/02/2020	11/17/2020
Note: Held By: PBUCKLEY All references below to the 2017 Florida Building Code-Plumbing 1. Replace plumbing riser note with note applicable to this building. 2. Based on the estimated number of plumbing facilities the building drain shall be 4 inch minimum if serving all four tenant spaces. If individual building drains / building sewers are proposed independent to each tenant space please indicate as much and show locations, materials, size, etc. 3. Provide complete plumbing equipment schedule. 4. Provide location, materials specifications and size of building sewer(s) and water service(s). 5. Provide complete water piping and drain, waste and vent material schedule. 6. Provide plumbing hanger and support schedule. 7. Remove note indicating duct layout and other partial illegible note. 8. Provide location and specifications for water heater in proposed tenant space.
UD1	HOLD	11/02/2020	11/06/2020
Note: Held By: CJOHNSON Provide water service layout and riser.

Fees & Payments

(Permit is not ready for pickup until the permit has been processed and fees appear)

Description	Amount Due	Date Paid
ADMIN COMMERCIAL	¤60.00	03/08/2021
BUILDING DISCOUNT 100%	(¤3,197.50)	03/08/2021
ELECTRIC FEE	¤270.00	03/08/2021
IMPACT FEE FIRE	¤8,850.00	03/08/2021
IMPACT FEE TRANSPORTATION	¤25,920.00	03/08/2021
MECHANICAL FEE	¤270.00	03/08/2021
PERMIT FEE	¤1,925.00	03/08/2021
PLAN CHECK FEE	¤402.50	03/08/2021
PLUMBING FEE	¤270.00	03/08/2021
SITE PLAN 20	¤20.00	03/08/2021
SURCHARGE FS 533.721	¤2.00	03/08/2021
SURCHARGE - FS 468.631	¤2.00	03/08/2021
Fees	Total Due: ¤0.00	Total Paid: ¤34,794.00