I want to search for...
Permit #2023121138
Permit Details
Status: FINAL
| Parcel Id: 05-11-31-4075-00070-0210 |
| Block: 00070 |
| Subdivision: 1127 - MARINA COVE |
| Job Phone: 386-585-0958 |
| Location Address: 21 MARINA POINT PL |
| Type: BIA - BUILDING INTERIOR EXTERIOR ALTERATION |
| Issue Date: 04/08/2024 |
| NOC: RECORDED |
| Applicant name: JEFFREY G SPRAGUE |
| Owner: FANNON LARRY STEPHEN & INDIA CUBINSKI |
|
Address 21 MARINA POINT PL PALM COAST, FL 32137 |
| Lot: 0210 |
| Contracted Stated Job Value: ¤5,544.00 |
| Job Description: Roof renovation |
| Type: CN |
Contractor
JGS DESIGN ASSOCIATES, LLC
| Status | Location Address | State License Number | Phone |
| INACTIVE |
8 INDIAN MOUND CT FLAGLER BEACH, FL 32136 |
CBC1260630 (Exp: 08/31/2026) | 386-585-0958 |
Inspection History
| Type | Request Date | Result | Inspector |
| BLD - BUILDING FINAL | 05/28/2024 | FINAL APPROVED | JWALKER |
| INSULATION | 05/14/2024 | APPROVED | JWALKER |
| ALL ROUGH | 05/14/2024 | Disapproved - NO FEE | JWALKER |
| Note: Gate Code 1033 provide to the city did not work. The contractor will need to leave the gate code in the applicant notes below. It is my understanding the gate code changes frequently at this location. | |||
| ALL ROUGH | 05/14/2024 | APPROVED | JWALKER |
| Note: 5/14/2024 - PREVIOUS INSPECTION NOTES Gate Code 1033 provide to the city did not work. The contractor will need to leave the gate code in the applicant notes below. It is my understanding the gate code changes frequently at this location. | |||
| ROOF SHEATHING / BRACES/TIES/DOWN CELL | 05/09/2024 | APPROVED | LMILLER |
| Note: 5-9-24 prior notes resolved 5/8/2024 - PREVIOUS INSPECTION NOTES 5-8-24 repair was not completed per approved engineers repair detail. (Flitch plarte was cut to allow the strong tie to remain) also check nailing pattern to be sure it complies with the approved repair detail 5/3/2024 - PREVIOUS INSPECTION NOTES 5/1/2024 - PREVIOUS INSPECTION NOTES 5-1-24 1. Plywood missing nails at 4 inches OC at panel edges per plan note 2 under Lumber on sheet S2.0and within 5 feet of the ridge and edge around perimeter 2. Missing 2x4 SYP blocking w/2 inch diameter ventilation sawhole per Sheet S1.0 Eave/Soffit Detail 1 3. 2x8 valley plate missing 3 inch Simpson strong drive SS SDWS stating at 16 inches OC per note 2 under key notes on sheet S1.0 4. 2x8 ledger plate missing 2- half inch x 5 inch galv. Lag bolts starting at 4 inches of each end and at 32 OC max per note 3 under key notes on sheet S1.0 5. Missing new 2x8 SYP PT Cont. Fastened to top of CMU wall w/1 half inch x 6 inch anchor bolt w/washer starting 4 inches of each end and 32 OC max 6. Rafters cannot be notched more than one fourth the rafter depth R802.7.1 Sawn lumber. Cuts, notches and holes in solid lumber joists, rafters, blocking and beams cannot be cut or notched more than one fourth the depth of the board and must bear on the heal portion of the cut per FBC-R 802.7.1 and figure 802.7.1.1 and 802.7.1.2 4/19/2024 - PREVIOUS INSPECTION NOTES Not ready for inspection, Not complete, Still working, Please do not schedule inspections before the work is complete. | |||
| ROOF SHEATHING / BRACES/TIES/DOWN CELL | 05/08/2024 | Disapproved -FEE REQUIRED | LMILLER |
| Note: 5-8-24 repair was not completed per approved engineers repair detail. (Flitch plarte was cut to allow the strong tie to remain) also check nailing pattern to be sure it complies with the approved repair detail 5/3/2024 - PREVIOUS INSPECTION NOTES 5/1/2024 - PREVIOUS INSPECTION NOTES 5-1-24 1. Plywood missing nails at 4 inches OC at panel edges per plan note 2 under Lumber on sheet S2.0and within 5 feet of the ridge and edge around perimeter 2. Missing 2x4 SYP blocking w/2 inch diameter ventilation sawhole per Sheet S1.0 Eave/Soffit Detail 1 3. 2x8 valley plate missing 3 inch Simpson strong drive SS SDWS stating at 16 inches OC per note 2 under key notes on sheet S1.0 4. 2x8 ledger plate missing 2- half inch x 5 inch galv. Lag bolts starting at 4 inches of each end and at 32 OC max per note 3 under key notes on sheet S1.0 5. Missing new 2x8 SYP PT Cont. Fastened to top of CMU wall w/1 half inch x 6 inch anchor bolt w/washer starting 4 inches of each end and 32 OC max 6. Rafters cannot be notched more than one fourth the rafter depth R802.7.1 Sawn lumber. Cuts, notches and holes in solid lumber joists, rafters, blocking and beams cannot be cut or notched more than one fourth the depth of the board and must bear on the heal portion of the cut per FBC-R 802.7.1 and figure 802.7.1.1 and 802.7.1.2 4/19/2024 - PREVIOUS INSPECTION NOTES Not ready for inspection, Not complete, Still working, Please do not schedule inspections before the work is complete. | |||
| ROOF SHEATHING / BRACES/TIES/DOWN CELL | 05/03/2024 | CANCELLED BY APPLICANT | JWALKER |
| Note: 5/1/2024 - PREVIOUS INSPECTION NOTES 5-1-24 1. Plywood missing nails at 4 inches OC at panel edges per plan note 2 under Lumber on sheet S2.0and within 5 feet of the ridge and edge around perimeter 2. Missing 2x4 SYP blocking w/2 inch diameter ventilation sawhole per Sheet S1.0 Eave/Soffit Detail 1 3. 2x8 valley plate missing 3 inch Simpson strong drive SS SDWS stating at 16 inches OC per note 2 under key notes on sheet S1.0 4. 2x8 ledger plate missing 2- half inch x 5 inch galv. Lag bolts starting at 4 inches of each end and at 32 OC max per note 3 under key notes on sheet S1.0 5. Missing new 2x8 SYP PT Cont. Fastened to top of CMU wall w/1 half inch x 6 inch anchor bolt w/washer starting 4 inches of each end and 32 OC max 6. Rafters cannot be notched more than one fourth the rafter depth R802.7.1 Sawn lumber. Cuts, notches and holes in solid lumber joists, rafters, blocking and beams cannot be cut or notched more than one fourth the depth of the board and must bear on the heal portion of the cut per FBC-R 802.7.1 and figure 802.7.1.1 and 802.7.1.2 4/19/2024 - PREVIOUS INSPECTION NOTES Not ready for inspection, Not complete, Still working, Please do not schedule inspections before the work is complete. | |||
| ROOF SHEATHING / BRACES/TIES/DOWN CELL | 05/01/2024 | Disapproved - NO FEE | LMILLER |
| Note: 5-1-24 1. Plywood missing nails at 4 inches OC at panel edges per plan note 2 under Lumber on sheet S2.0and within 5 feet of the ridge and edge around perimeter 2. Missing 2x4 SYP blocking w/2 inch diameter ventilation sawhole per Sheet S1.0 Eave/Soffit Detail 1 3. 2x8 valley plate missing 3 inch Simpson strong drive SS SDWS stating at 16 inches OC per note 2 under key notes on sheet S1.0 4. 2x8 ledger plate missing 2- half inch x 5 inch galv. Lag bolts starting at 4 inches of each end and at 32 OC max per note 3 under key notes on sheet S1.0 5. Missing new 2x8 SYP PT Cont. Fastened to top of CMU wall w/1 half inch x 6 inch anchor bolt w/washer starting 4 inches of each end and 32 OC max 6. Rafters cannot be notched more than one fourth the rafter depth R802.7.1 Sawn lumber. Cuts, notches and holes in solid lumber joists, rafters, blocking and beams cannot be cut or notched more than one fourth the depth of the board and must bear on the heal portion of the cut per FBC-R 802.7.1 and figure 802.7.1.1 and 802.7.1.2 4/19/2024 - PREVIOUS INSPECTION NOTES Not ready for inspection, Not complete, Still working, Please do not schedule inspections before the work is complete. | |||
| ROOF SHEATHING / BRACES/TIES/DOWN CELL | 04/19/2024 | Disapproved -FEE REQUIRED | LMILLER |
| Note: Not ready for inspection, Not complete, Still working, Please do not schedule inspections before the work is complete. |
Review History
| Department | Status | Date In | Date Out |
| BLD | COMPLETE | 05/03/2024 | 05/07/2024 |
| Note: Released By: JOSH MUNSON - (386)986-4736 - JMUNSON@PALMCOASTGOV.COM | |||
| BLD | COMPLETE | 04/02/2024 | 04/08/2024 |
| Note: Released By: JIM WALKER - (386)529-4112 - JWALKER@PALMCOASTGOV.COM | |||
| BLD | HOLD | 03/27/2024 | 04/02/2024 |
| Note: Held By: JOSH MUNSON - (386)986-4736 - JMUNSON@PALMCOASTGOV.COM 2. Provide completed product approval worksheet. Include soffit material and structural components. provide decimal point for all products 3. Soffits are over 12 inches. Provide midpoint span on detail per 1410.3 FBC Building 2023 8th edition 4. Roofing worksheet that was uploaded is not the most current. 5. Roofing underlayment number needs to be updated to the most current code cycle. | |||
| BLD | HOLD | 03/25/2024 | 03/25/2024 |
| Note: Held By: CHRIS PISCITELLI - (386)986-2574 - CPISCITELLI@PALMCOASTGOV.COM THIS IS THE CORRECT REVIEW. PREVIOUS WAS DONE IN ERROR 1. Provide decimal points for all products on roofing worksheet and product approval worksheet. 2. Provide completed product approval worksheet. Include soffit material and structural components. provide decimal point for all products 3. Soffits are over 12 inches. Provide midpoint span on detail per 1410.3 FBC Building 2023 8th edition | |||
| DSD | COMPLETE | 03/19/2024 | 03/19/2024 |
| Note: Released By: JACQUELINE GONZALEZ - (386)986-3751 - JGONZALEZ@PALMCOASTGOV.COM | |||
| BLD | HOLD | 03/19/2024 | 03/25/2024 |
| Note: Held By: CHRIS PISCITELLI - (386)986-2574 - CPISCITELLI@PALMCOASTGOV.COM 1. Provide decimal points for all products on roofing worksheet and product approval worksheet. 2. Provide completed product approval worksheet. Include soffit material and structural components. provide decimal point for all products | |||
| BLD | HOLD | 12/28/2023 | 01/05/2024 |
| Note: Held By: PATRICK BUCKLEY - (386)986-3786 - PBUCKLEY@PALMCOASTGOV.COM 1. All plan sheets must have a verifiable digital signature / seal. Seals are manual type and some plan sheets have no seal. 2. Plan sheets, especially the "S" plan sheets are ilegible. They appear to be photocopies and are unreadable. 3. Provide City of Palm Coast Roofing Worsheet for roofing materials - underlayment and roof covering. 4. Provide authorization from HOA allowing work on this townhouse or condominium unit. 5. Not a complete plan review. Due to unreadable plans, additional comments may be forthcoming on submittal of readable plans. | |||
| ELEC | CANCEL | 12/28/2023 | 12/29/2023 |
| MECH | CANCEL | 12/28/2023 | 12/29/2023 |
| PLUM | CANCEL | 12/28/2023 | 12/29/2023 |
| DSD | HOLD | 12/28/2023 | 12/28/2023 |
| Note: Held By: DAMARIS RAMIREZ - (386)986-3750 - DRAMIREZ@PALMCOASTGOV.COM Provide a color material sheet. This sheet can be found on our website. https://www.palmcoast.gov/building |
Fees & Payments
(Permit is not ready for pickup until the permit has been processed and fees appear)
| Description | Amount Due | Date Paid |
| REINSPECTION RESIDENTIAL | ¤40.00 | 05/27/2024 |
| REINSPECTION RESIDENTIAL | ¤40.00 | 04/30/2024 |
| SURCHARGE FS 533.721 | ¤2.00 | 04/08/2024 |
| SURCHARGE - FS 468.631 | ¤2.00 | 04/08/2024 |
| SITE PLAN 30 | ¤30.00 | 04/08/2024 |
| ADJUSTMENT 50% | (¤77.50) | 04/08/2024 |
| ADMINISTRATIVE RESIDENTIAL | ¤30.00 | 04/08/2024 |
| INSPECTION - RESIDENTIAL | ¤60.00 | 04/08/2024 |
| PLAN REVIEW - RESIDENTIAL | ¤65.00 | 04/08/2024 |
| Fees | Total Due: ¤0.00 | Total Paid: ¤191.50 |